Read Iveco EDC7UC31 by FGTech Galletto and Ktag

Here are two optional solutions of how to read Iveco EDC7UC31 Bosch ECU by using FGTech galletto and Ktag ksuite v2.10 respectively.

This is the Iveco truck ECU Bosch EDC7UC31 to read:

Solution 1: Ktag v2.10 read EDC7UC31 Bosch ECU

Tested with Ktag master ecu tuning kit firmware v5.001 and ksuite v2.10 software from obdii365.com

Here goes to the ecu reading process…

Select truck-> Iveco truck-> Cursor B-> Bosch EDC7UC31 to read the ecu data

Note: there are lots of Ktag clones with different firmware & software versions. Some are designed for cars, some for trucks. But sometimes even the truck version fails to do on trucks. So the real fact only can be learned by testing yourself, with luck.

Solution 2: FGTech 2 & special adapter read Iveco EDC7UC31 without issues

The FgTech galletto 2 master ecu programmer is offered by obdii365.com also.

The process of EDC7UC31 ecu reading…

Note: EDC7UC31 ecu reading through galletto needs luck. Some people in forums said they failed to this. Even the experienced

– So which ecu programmer you should choose to read EDC7UC31 ecu?

–  It depends. Both can read EDC7UC31 successfully, with disassembling the ecu. Here list some aspects for you to think about your purchase.

Price:

K-tag v2.10: $79.00 

Fgtech 2: $29.99

Reading speed:

Ktag: about 5 minutes to complete the ecu reading

Fg tech: about 3 minutes for it

–> Conclusion:

They both work good, but KTAG runs without tokens limitation, perfect with checksum, compared with FGTech.

Good luck when reading EDC7UC31 ecu.

http://blog.obdii365.com/2016/11/27/read-iveco-edc7uc31-ok-with-fgtech-ktag/

Flash EDC16 & Me9 ECU by Fgtech Galletto via BDM

Have tried to flash EDC16 with KESS V2 clone, but i can not see anymore HW and VIN from the EDC16 ECU and the car not starts! Then worked with Fgtech Galletto v54 master, all EDC 16 on BDM without any problem… (BIG thanks to maki1)

Here is what i did with the EDC16U34 from VAG ECU, using Fgtech galletto v54.

The BDM pad here

Now carefully align with the adapter springs drop and secure frame

Connect FgTech galletto correctly

Open FgTech software

Make sure you have 12v+ feeding FG Tech and the intermediate adapter

Switch the intermediate adapter ON

Red LED will illuminate

Click on Select Driver-> BDM/Jtag-> Connect

If everything is ok, the green bar will start loading and finally display ECU info

When finished, turn off the switch and exit program

Same procedure applies to all EDC16

In short,

we need flash the ECU with BDM if we have full flash for this ECU…

open ECU and read all with BDM…

must find full flash hw and sw version for this ECU…

when write chose flash,not not all (eeprom and MCU not need).

Note: This method applies to all Bosch EDC16 and Me9 ECUs.

http://blog.obdii365.com/2016/11/14/fgtech-galletto-flash-edc16-me9-ecu-via-bdm/

Fgtech Galletto 4 V54 blocked by Internet Solution

Here is the working solution to Fgtech Galletto 4 V54 master ecu programmer blocked problem.

Question: FGtech V54 blocked help please.
I have Galletto FG tech 4 V54 clone, and blocked for internet update. Someone can help me??? Please help me as to how to download it to version that will make it work, please i need guidelines and url and where to get the lower firmware.

PROBLEM SOLVED
I reinstall the software and drivers en other computer. Run the software and see one banner "Galleto error an ocurred and close." . Reinstall the software (double click in setup,only reinstall software) without erase back installation and drivers. Fgtech galletto locked problem solved. more information see. Enjoy!