Question:Can you read and write edc17c19 with fgtech galletto? Anyone have experience ?? I can't find much info ... Maybe somebody done with galetto and can give instructions ???
Experience:
1). Galletto works with this ECU without any problems, manual for tricore in app folder.
2). It is possible to read it in boot mode with galetto.
3). Kess china work on obd... I tested on insignia of 2010 with kess v2 2.23 and 2.47...
4). i recommend you to flash with galletto or else over boot mode. Its the safest way. Ok, you can try to flash over obd. If you car wont start, you can recover over boot / bdm with ktag galletto or else, if you have. If you don't have, some tools, go save and flash by boot mode.
FgTech Galletto 4 Master V54 ECU programming tool software, installation and technical support.
Showing posts with label kess v2. Show all posts
Showing posts with label kess v2. Show all posts
12/09/2019
Will Fgtech Galletto read Edc17c19 ECU?
loading..
5/11/2018
Read Bosch EDC15P+ Boot with MPPS, Fgtech or Kess V2?
Question before entering:
I have some trouble with my spare EDC15P+ ECUs. I have now invested in a MPPS V21 because of its booting capabilities! But No matter what i do, MPPS keeps saying “Booting of ECU failed” or it freezes during connection establishment. I have tried this om 3 different ECU’s with bad flash and 2 PC’s.
The procedure i use:
Generic -> Micro Boot -> EDC15P -> Pin 24 to ground and Power On -> Remove ground from Pin 24 -> Select ECU ID
Generic -> Micro Boot -> EDC15P -> Pin 24 to ground and Power On -> Remove ground from Pin 24 -> Select ECU ID
Happens every time and it’s driving me nuts. I have bought MPPS for the sole purpose of recovering bad ECU’s, so i really hope that some of you maybe can help me with this.
Expert solutions:
Solution 1: with MPPS
With MPPS V21, you need luck. V21 maybe too new to this ecu.
Check with multimeter pin140 to pin44 and pin104 to pin24.
I bought MPPS HW12 china clone, software v16 for hardware 12. For a long time ago I had a similar problem with VW Sharan , I do not remember exactly how I was reinstall the firmware on it. But finally it works. Here are some pictures:
Solution 2:
MPPS V13 no problem on this ecu
I try read with kess v2 and mpps v21 edc15p+ and I get error, but with mpps v13 no problem to reading this ecu on table.
So i finally got my spare ECU’s working again. I ordered a MPPS v13 ecu flasher, and that one was able to bootflash all the ECU’s.
Solution 3:
Kess v2 master read EDC15P+ on bench on issues
Testing edc15p+ of a Seat Ibiza
Solution 4:
Fgtech Galletto V54 on bench Writing vw EDC 15 P+ no problem
VW pasat 1.9 PD writing edc 15p+ 115 mph up to 130mph and egr off.
loading..
1/16/2018
What tool can read for tuning opel ME7.6.2 ecu
Here are solutions to unlock this ECU: Astra H 2.0 Bosch Me7.6.2.
Q:
Hello can tell me any good tool for reading opel ecu for chip tuning.
Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa.
Bosch ME.7.6.2 – Z16LET – Z14XEP Astra H and Corsa.
Option 1: SMOK
opel all from smok !!!! can help with this ecu
Supported ECU CAN and available functions:
Bosch ME762 Read EE, Read PIN, Read/Write KM, Change VIN, Reset ECU
Supported ECU Kline and available functions:
Bosch ME762 Z10XE,Z12XE (opel corsa,combo,astra)-Read PIN, Reset ECU ,Change VIN
Note: We don’t have smok, you can buy from smok.com.pl.
Option 2: MPPS V21
I’ve once read something about latest ori MPPS being able to unbrick these:
MPPS v21.2.1.8 released
OBD:
Opel ME7.6.2 – Special mode added R/W/Cks Kline/CAN
Opel ME7.6.2 – Special mode added R/W Eeprom Kline/CAN
Option 3: FGTech Galletto 4 v54
Try boot mode, these ECUs are not recoverable very easy if boot mode not work
Galletto has full mode for this ecu k +CAN, reads the eeprom on bench.
Option 4: Genuine carprog
ME7.6.2 PINOUT at connection CARPROG should read pin vin and reset. Good luck with that its an uncased prom . genuine carprog works 100% via OBD and on the bench.
Option 5: Kess V2
Kess v2 can do that.
China kess v2 will do it but need to rework.
Kess v2 tested on ME 7.6.2 by Russian technician.
Option 6: GM MDI multiple interface
the only solution that maybe work is. flash ori with mdi or byteshooter
Good luck!
Reference:
Opel Bosch ME7.6.2 ECU’s
| Tigra B | Z14XEP | 2005 – 2009 |
| Astra H | Z14XEP Z12XEP Z14XEL Z20LER Z20LEL Z20LEH Z16LET | 2004 – 2009 2006 – 2009 2004 – 2009 2005 – 2009 2004 – 2009 2005 – 2009 2007 – 2009 |
| Corsa D | Z14XEP Z12XEP Z10XEP Z16LER | 2007 – 2009 2007 – 2009 2007 – 2009 2007 – 2009 |
| Zafira B | Z20LER Z20LEH | 2005 – 2008 2006 – 2009 |
loading..
7/13/2017
How to install Professional PDF EGR remover software on WinXP
Here is the step-by-step on installing Professional DPF+EGR REMOVER 3.0 Lambda Hotstart Flap,O2, DTC 2 full software.
Software: 2016.02
Software for ONE laptop
Operating system: WinXP to Win8.1, Win10 (32 + 64 bits)
Multi-language: English, German, French, Spanish, Italian, Turkish, Slovak – Czech, Romanian, Portuguese, Polish, Dutch
Compatible programmer: Fgtech Galletto, KESS V2, K-tag Master, MPPS, CMD ect. readers – File writers work 100% with these programs.
Bosch, Siemens, Denso, Visteon, Delphi, Marelli ECU Transtron are supported !!
How to install Professional PDF EGR remover software? (Example on WinXP)
Open and unzip Professional PDF remover.zip and Professional EGR remover.zip file on desktop separately
Open Professional PDF remover on desktop, select software Language
Welcome to PDF remover setup wizard, click on Next
Tick "Create a Desktop Icon", click on Next
click on Install
Open Professional EGR remover software on desktop
select software language
Welcome to Egr remover setup wizard, click on Next
Tick "Create a Desktop Icon", click on Next
click on Install
EGR remover has been installed, click Finish to close this wizard.
Delete both PDF remover and EGR remover on desktop
Create a new txt notepad name "id"
Open Professional PDF remover shortcut on desktop,
copy HWID to notepad
Open Professional EGR remover shortcut on desktop,
copy HWID to notepad
Please send the activation ID to our customer service
Click yes to save the changes.
Then we will send you license file
Extract license.zip (containing PDF and EGR folders)
Delete license.zip
Open PDF folder, there is a data bin file
Right click Professional PDF remover shortcut->Properties, Find Target to go to
C:/Program Files/Professional PDF remover,
Cut and paste data bin file to C:/Program Files/Professional PDF remover
Then delete PDF folder on desktop
Open Professional PDF remover shortcut
Launch software,click on Setup button to select language and use the removal
software ready to use
Open EGR folder, there is a data bin file
Right click Professional EGR remover shortcut->Properties, Find Target to go to
C:/Program Files/Professional EGR remover,
Cut and paste data bin file to C:/Program Files/Professional EGR remover
Then delete EGR folder on desktop
Open Professional EGR remover shortcut
click on Setup button to select language and use the removal
software ready to use
loading..
Subscribe to:
Posts (Atom)


















































