Fgtech Galletto V54 master "required new tool 2012"

Problem:
One of obdii365 customer want to program Citroen 1.6 HDi EDC16 and vw golf 6 1.6 tdi pcr 2.1 online with Fgtech galletto 4 v54 master BDM-Tricore-OBD programmer, but the fgtech v54 software prompts error message "required new tool 2012"

Solution:
Check if the Fgtech galletto driver is well installed and change another laptop running Win XP mode. 

If still not working,sorry the galletto will not work on your ECU. 

http://www.obdii365.com/upload/pro/201506/new-fgtech-v54-supported-ecu-list-after-test-obd365.pdf

Fgtech Galletto V54 K-line not working customer solution

Here is the customer solution to the Fgtech Galletto master ecu programmer k-line not working issue.

Question:

any idea to repair this old Fgtech v54 k-line not working

Answer:

Replace 2x smd resistor

Swap 2700 for 270 ohm

Swap 4700 for 470 ohm

Change HCF40106 for HEF40106BT

http://www.obdii365.com/wholesale/v54-fgtech-galletto-4-master-bdm-tricore-obd-function.html

Fgtech Galletto 4 v54 unlock ecu error solution

I have simos pcr 2.1 ecu , i want to unlock but the Fgtech galletto 4 v54 master displayed error unknown ecu

I think dashboard on / off problem

12v charger I put, but one extra batter supply given or not ?

Here I attach picture of connection but not succeed.

Working Solution:

Remove 25640 put in programmer and unlock refit write ecu obd…..

Apply 12v dc adaptor to fgtech galletto, not battery supply to fgtech v54.

Add only 2 resistors, not 3 ones.
560 ohm and 1K ohm and one wire to make a bridge.

Recover FTDI eeprom when Fgtech Galletto is not recognized

This is the instruction on how to recover FTDI eeprom even if gtech Galletto v54 is not recognized correctly by Windows.

Tools i used is FGTech Galleto 4 master from China, with the link:http://www.obdii365.com/wholesale/v54-fgtech-galletto-4-master-bdm-tricore-obd-function.html

Free download Galletto V54 FTDI files:

Galletto_V54_FTDI_Full_Recovery.rar

FTDI files included:

folder “FIX1”

folder “FIX2”

Recovery procedure:

1. Connect Galletto v54 to USB, run Device Manager and install drivers for not recognized Galletto from directory “FIX1\Standard FTDI Drivers for recovery”

2. Run MProg.exe, open the file “Galetto_v54.ept” and press “Program”

3. Disconnect UBS and connect back.

Now Galletto will be recognized, but not fully programmed.

4. Go to “FIX2” directory and run FTReadWrite_v3.exe, press “Write” and open 54.bin file.

FGTech galletto v54 “Can not find driver” problem

Problem:

When install FGTech galletto 4 V54 master software, the FTReadWrite replied “Can’t find device” error message. When trying to uninstall the driver, the window screen warmed it is not FGTECH device, but USB-to-Serial device. If install the driver, fgtech v54 software did not run and FTReadWrite or MProg didn't find the ftdi chip. Try to install the driver on both win 7 and win xp computer over and over, but in vain.

Solution:

1) Download and install the Virtual Com Port drivers from FTDI website:

Virtual COM Port Drivers

http://www.ftdichip.com/Drivers/VCP.htm

2) Then connect the FGTech to computer via USB port which had no device programmed and 1 blank device when the MProg Utility it shows.

NOTE: If you had backup and reprogram with the ept file. The system will not recognize the FGTECH and will not reprogram the firmware bin file. The Virtual Com Port Drivers would overlay the fgtech ECU programmer. Then you have to again download the related driver in FTDI website.

CMD Uninstaller 1.4

http://www.ftdichip.com/Support/Utilities.htm

3) After install the right drivers, FTReadWrite programmed the backup firmware file, run galletto v54 software by referring to the user manual on obdii365 webpage.

FgTech Galletto V54 read and write ST10Fxx via Tricore Boot Mode

FgTech Galletto v54 master is properly the most user-friendly ECU tuning kit comparing with other clone master version (like KESS or MPPS). My two sets of FgTech galletto ECU programmers (one main unit and another with additional BDM Frame) were delivered from obdii365.com for less than 45 bucks.

Galletto Software was not difficult to install within 3 minutes.

Here I successfully read and write SF10Fxx (K-Line) via Tircore Boot Mode. The FgTech v54 ECU tuning box would prompt which way you are going to read and write the ECU (via OBD, BDM or Tircore boot mode).

After well install and connect FgTech galletto ecu programmer, come to software main program, select vehicle and engine type

Select “Read” and then “Write”, well, it is quite easy

I have tested some other models:

EDC16U1 (VAG) Read/Write ok (OBD)

EDC15V (VAG) Read/Write ok (OBD)

Audi A6 (TRICORE BOOT)

E70 3.0D EDC16 (BDM)

Renault Delphi 2007 k-line

Still leaning on it and will list all tested work ECUs by mini Galletto master.

Fgtech Galletto V54 fixed BMW X5 V8 4.8i ecu no start

I have one big problem with BMW X5 V8 4.8i ecu, the car no start. Starter relay and fuel pump relay turn on-turn off-turn on-turn off-turn on-turn off (intermittence synchronize between two relays).Battery is Ok. Ground connections from engine is OK. Strange it fails. OBD2 scan tool not recognize.

ECU chip tuning tool I use:

Fgtech Galletto 4 V54 master. I can read flash and micro with Fgtech with BDM mode.

Pin out for this BoschECU...
looking from the left: as the above pictures...
Socket 1st:
pin_7 and 8 +12v
pin_4,5,6-grnd
socket 4th:
pin32-_diagnosis
pin36_CAN-L
pin37_CAN-H
pin26-+12v
socket 5th:
pin5-grnd

Finally, solve!!!

Read points with BDM system. (Read with Fgtech galletto  v54) For security verify correctly ground pin position.